XDE-RTTY 2.1.0 — What's new / Novità
by IK2XDE Andrea · https://www.xdenews.net/xdertty/
=====================================================================

ENGLISH

2.1.0
* New TX DELAY (Settings → Transmit): a short silence after PTT before
  any RF, so the radio and the amplifier are already in TX.
* Updated to the TCI 2.1 protocol: if the radio does not allow
  transmitting on a band, a clear message appears at once.
* REC: the RX audio is now saved as MP3 (about 8 times smaller); the
  I/Q recording stays WAV.

2.0.9
* SPLIT UP: the radio's DIGU setting is adjusted by itself and put back
  afterwards: nothing to change by hand between RTTY and FT8/FT4.
* TCI address preset to ws://127.0.0.1:50001 (can be changed).
* Now also for Linux (beta).

2.0.8
* New CALL DATABASE UPDATE: more stations recognised on the waterfall
  and the bandmap, fewer false calls; kept up to date automatically.

2.0.7
* New NB (noise blanker) and NOTCH (automatic notch) in the RX panel:
  better copy with static crashes and with carriers near the signal.

2.0.6
* Improved STANDARD decoder in noise and fading.
* Faster AFC: a caller slightly off frequency is copied at once.
* Reports and numbers copied more often correctly.
* QSO window and spectrum: larger frequency display.

2.0.5
* Bandmap and waterfall: further improved choice of the stations shown.

2.0.4
* Bandmap: improved choice of the stations shown.

2.0.3
* Bandmap and waterfall: improved recognition of the station on each
  signal.
* SPLIT UP 12.5K: waterfall and spectrum show the whole window.

2.0.2
* QSO sending over UDP in WSJT-X format improved: QSOs are now
  logged by WSJT-X compatible loggers; QTH and note in their own fields.

2.0.1
* More stations on the waterfall and the bandmap (improved multi-decoder).
* SPLIT UP: 12.5K replaces 15K and 20K, which the radio does not allow;
  the span follows the filter the radio really sets.
* Settings: date of the SCP file in use.
* Manuals updated with new pictures.

2.0.0
* New RX decoder layout: STANDARD and DX NOISE FILTER always open side
  by side, SIMPLEX filters on the left, SPLIT UP filters on the right,
  squelch between the two windows.
* Default layout for 1920x1080 screens, bandmap at the right
  (Settings -> Default layout).
* News and updates on Telegram: t.me/xde_rtty

1.9.9
* SPLIT UP: new 15K and 20K receive windows; the window now starts
  0.5 kHz below the dial. The multi-decoder follows more stations.
* After a band change on the radio, filter and span go back to the
  default (SIMPLEX 500 Hz, span 2 kHz).
* Updates install without showing a console window.

1.9.8
* General code optimisation.
* Manuals updated.

1.9.7
* Bandmap: more stations shown; calls not yet in the SCP database
  appear in light blue.
* QSO form: new "Loc" field (WW locator), filled with a click in the RX
  window like Name and QTH; saved in the log, ADIF and UDP.
* REC: just "SAVED" at the end of a recording.

1.9.6
* Improved receiver (STANDARD decoder and multi-decoder).
* Improved squelch; AUTO button next to SQ.

1.9.5
* REC: receive-only recordings (RX audio, text of both RX windows,
  optionally I/Q), in folders by date and band.
* Bandmap: uncertain calls in light blue.

1.9.4
* Automatic update; this file opens after each update.

1.9.0 - 1.9.3
* DX NOISE FILTER: a second decoder for weak and fading signals.
* Improved STANDARD decoder. Your own callsign is never spotted.


ITALIANO

2.1.0
* Nuovo TX DELAY (Impostazioni → Transmit): breve silenzio dopo il PTT
  prima della RF, così radio e amplificatore sono già in TX.
* Aggiornato al protocollo TCI 2.1: se la radio non consente di
  trasmettere su una banda, compare subito un messaggio chiaro.
* REC: l'audio RX ora viene salvato in MP3 (circa 8 volte più piccolo);
  la registrazione I/Q resta in WAV.

2.0.9
* SPLIT UP: l'impostazione DIGU della radio viene regolata da sola e poi
  rimessa com'era: niente da cambiare a mano tra RTTY e FT8/FT4.
* Indirizzo TCI già impostato a ws://127.0.0.1:50001 (modificabile).
* Ora anche per Linux (beta).

2.0.8
* Nuovo CALL DATABASE UPDATE: più stazioni riconosciute su waterfall e
  bandmap, meno nominativi falsi; aggiornato in automatico.

2.0.7
* Nuovi NB (noise blanker) e NOTCH (notch automatico) nel pannello RX:
  ricezione migliore con scariche e con portanti vicine al segnale.

2.0.6
* Migliorato il decoder STANDARD con rumore e fading.
* AFC più veloce: un corrispondente leggermente fuori frequenza viene
  copiato subito.
* Rapporti e numeri letti correttamente più spesso.
* Finestra QSO e spettro: frequenza più grande.

2.0.5
* Bandmap e waterfall: ulteriormente migliorata la scelta delle stazioni
  mostrate.

2.0.4
* Bandmap: migliorata la scelta delle stazioni mostrate.

2.0.3
* Bandmap e waterfall: migliorato il riconoscimento della stazione su
  ogni segnale.
* SPLIT UP 12.5K: waterfall e spettro mostrano tutta la finestra.

2.0.2
* Migliorato l'invio dei QSO via UDP in formato WSJT-X: ora i QSO vengono
  registrati dai log compatibili WSJT-X; QTH e nota nei rispettivi campi.

2.0.1
* Più stazioni sul waterfall e nella bandmap (multi-decoder migliorato).
* SPLIT UP: il 12.5K sostituisce 15K e 20K, che la radio non consente;
  lo span segue il filtro realmente impostato dalla radio.
* Impostazioni: data del file SCP in uso.
* Manuali aggiornati con nuove immagini.

2.0.0
* Nuova disposizione del decoder RX: STANDARD e DX NOISE FILTER sempre
  aperti e affiancati, filtri SIMPLEX a sinistra, filtri SPLIT UP a
  destra, squelch tra le due finestre.
* Disposizione iniziale per schermi 1920x1080, bandmap a destra
  (Impostazioni -> Default layout).
* Novità e aggiornamenti su Telegram: t.me/xde_rtty

1.9.9
* SPLIT UP: nuove finestre di ricezione 15K e 20K; la finestra ora
  parte 0,5 kHz sotto il dial. Il multi-decoder segue più stazioni.
* Dopo un cambio banda sulla radio, filtro e span tornano al default
  (SIMPLEX 500 Hz, span 2 kHz).
* Gli aggiornamenti si installano senza mostrare una finestra di console.

1.9.8
* Ottimizzazione generale del codice.
* Manuali aggiornati.

1.9.7
* Bandmap: più stazioni visualizzate; i nominativi non ancora presenti
  nel database SCP compaiono in azzurro.
* Modulo QSO: nuovo campo "Loc" (WW locator), riempito con un clic nella
  finestra RX come Name e QTH; salvato nel log, in ADIF e in UDP.
* REC: a fine registrazione compare solo "SAVED".

1.9.6
* Migliorato il ricevitore (decoder STANDARD e multi-decoder).
* Migliorata la gestione dello squelch; pulsante AUTO accanto a SQ.

1.9.5
* REC: registrazioni in sola ricezione (audio RX, testo delle due
  finestre RX, a scelta I/Q), in cartelle per data e banda.
* Bandmap: nominativi incerti in azzurro.

1.9.4
* Aggiornamento automatico; questo file si apre dopo ogni aggiornamento.

1.9.0 - 1.9.3
* DX NOISE FILTER: un secondo decoder per segnali deboli e in fading.
* Migliorato il decoder STANDARD. Il proprio nominativo non viene mai
  spottato.
